SMOK SCAR-P3

Made with stylish leather and zinc alloy construction, the SMOK SCAR-P3 is IP67 waterproof and can withstand water immersion of up to 1 meter for up to 30 minutes with the charging port sealed. The SMOK IQ-80 chip inside this device provides all the standard protections you expect from a modern vape device, plus up to 80W of output power for massive vapor production if you want it.

Included in your kit are two SMOK SCAR-P3 pods with dual-channel direct airflow, which means air entering from either side of the pod forms a two-way vertical airflow channel with no loss of airflow. You’ll get maximum flavor and maximum vapor production with this design. Plus, each pod is compatible with different types of SMOK RPM or RPM 2 Coils, so whether you prefer high nicotine salt liquids at low wattages or low nicotine freebase liquids at higher wattages, intense flavor, or big clouds, there’s a coil and a setting for you with the SCAR-P3.

SMOK SCAR-P3 Includes:

(1) SCAR-P3 Device

(1) 5.5ml SCAR-P3 RPM 2 Pod

(1) 0.16 ohm RPM 2 Mesh Coil (pre-installed, 25W-50W)

(1) 5.5ml SCAR-P3 RPM Pod

(1) 0.4 ohm RPM Mesh Coil (pre-installed, 25W)

(1) USB Type-C Cable

User Manual

SMOK SCAR-P3 Features

- Button Activated Design

- IP67 Waterproof, Dustproof & Shock-Resistant

- Three-Button Design: single power button, dual adjustment buttons

- Silicone-stoppered Top Fill Port: no need to remove the pod to refill

- Puff Monitoring System

- Intelligent Atomizer Recognition

- Multiple Protections: Short Circuit, Over-heating, Low Battery, 8 Second Cutoff

SMOK SCAR-P3 Specifications

Dimensions: 110mm x 32.3mm x 27mm

Weight: 105g

Battery: 2000mAh Built-In Battery

Charging: USB Type-C Charging, 5V / Max 1.1A

Chipset: IQ-80

Wattage Output: 5W - 80W

Resistance Range: 0.2 ohms - 2.5 ohms

Screen: 0.96 TFT Color Screen

Eliquid Capacity: 5.5ml

Recommended VG/PG Ratio: 70% VG

Compatible Pods: SMOK SCAR-P3 Pods

Compatible Coils: SCAR-P3 RPM 2 Pod works with SMOK RPM 2 Coils

Compatible Coils: SCAR-P3 RPM Pod works with SMOK RPM Coils

How do I charge my SCAR-P3?

As with all devices with Li-ion batteries, you should charge your device completely before first use, and discharge your device fully (do not overdischarge) before charging again. This helps to set your device’s battery life.

Included with your SMOK SCAR-P3 Kit will be a USB-C charging cord. The SCAR-P3 is designed to be charging with a 1A wall adapter (not included) and the included Type-C charging cable. Connect your USB-C cord to your 1A wall adapter, then plug your adapter into a wall outlet or surge protector, then plug your SCAR-P3 device in to charge.

It is recommended to remove your SCAR-P3 Pod before charging your device, just in case of leakage. Always charge in a clean, dry area on a fireproof surface and monitor your device while charging.

What pods and coils are compatible with the SCAR-P3?

Your SCAR-P3 Kit will come with two different pods, each with one matching coil pre-installed in the pod. You’ll use a different coil with each pod. Other brands and types of pods will not fit in the SCAR-P3.

The 5.5ml SCAR-P3 RPM 2 Pod included in this kit is pre-installed with a 0.16 ohm RPM 2 Mesh Coil rated for use between 25W and 50W, but recommended for use at 40W. The SCAR-P3 RPM 2 Pod is compatible only with authentic SMOK RPM 2 Coils and other coils will not fit in this pod.

The 5.5ml SCAR-P3 RPM Pod you’ll also find in your kit is pre-installed with a 0.4 ohm RPM Mesh Coil recommended for use at 25W. You can use any authentic SMOK RPM Coil in the SCAR-P3 RPM Pod.